Why walk while you can seat? Use boost vehicle connect the road marking machine, the work efficiency will improve 2-3 times. Working speed: 16km/h(move forward), 10kn/h(move backward) Color: Yellow Engine: Honda 5.5P Gradeability: ≤ 60 degree Size: 1500×660×1030mm Weight: 80kg

LXD pre-marking machine is the assistant machine in road marking construction. It can mark the pre-marking freely according to the requirements of construction to avoid faulty marking. Also can accomplish 1-3 lines independently, which greatly improves the construction efficiency.  Function: it can make three baseline at the same time Max.width: 9m Size: 1300×900×1000mm Net weight: 128kg

It is used for cleaning the bleeding cement,mud,quick soil out from the road surface. It also can blow away the impurities and dust of road surface.It has advantages of improving working efficiency and save workforce. Engine: 5.5HP Honda gasoline engine Sweep strength: Adjustable Wind wheel: turbocharging Wind power: adjustable Steel wire brush: wear-resisting and soft steel brush Rubber wheel: Wear-resisting Size: 1180×560×860mm Weight: 50kg

The machine mounted on Truck JAC K5, Vehicle performance and equipment matching, can apply for ordinary vehicle license and according to the provisions of inspection and examination. The high pressure water pump and other special components are integrated and installed in the protective cover, which can be easily separated from the vehicle. Remove line width: maximum 30cm (adjustable from 15cm-30cm) Operating speed: 10-20m/min (according to line thickness) Engine: Weifang Weichai Power (Dowitz) Power: 255 kw Speed: 1800 r/min Pump speed: 500 cycles per minute Pressure: 2500bar

Working speed: removing rubber ≥ 800-1000m ²/ h Engine: Weifang Weichai Power (DEUTZ) Power: 255kw Speed: 1800r / min Pump speed: 500 times per minute Pressure: 1400bar Flow rate: 85L / min Plunger: cemented carbide 26 High pressure seal: imported high quality molding seal

Engine: 11.0HP(hand starting air-cooled four stroke gasoline engine) Working width: 180mm Working thickness: adjusted according to the situation of road surface,normally less than 3mm Work efficiency: 600-800m²per day Working life of Grinding head: 20,000m-30,000m Driving Method: Self propelled Strength: strong, middle or weak(adjusted) Weight: 162kg Size: 1200×650×980mm

LXD900 road marking paint remover is mainly used to remove cold paint lines. The imported Tupungato steel cutter head is hard and rotates fast. The cutter head has long operating life, and it is convenient to load and unload it.

Diesel engine: DEUTZ Power: 120KW Remove speed: 5-7m/min Remove width: 150-250mm Suction system: German Technology Open-type: non-pressure tank,can remove solid waste under construction Suction pressure: -0.4 Booster pump: Max. 6KG

It is used for removing all kinds of road marking lines with its high pressure water. It has advantages of easy operation, simple maintenance, high efficiency, without damaging road surface,environment friendly.

LXD-23CX Ride on type road marking removal is the best stripper in the history of mechanical stripper. The machine is characterized by low failure rate, high efficiency, no need to replace bearings, good road grinding effect, easy maintenance and so on. This machine has various tool head modes, which can meet the requirements of various road surfaces.

Working pressure: 7bar, Silent safety valve Power Systems: 12V Thermoplastic container: 0.39m³, with hydraulic agitator (According to customer requirements) Heating method: Gas heating Additional equipment: Available with 15.20.30.40cm scraper, oscillating bucket (customized as required) Additional equipment: On request, profiles

It is professional equipment which is widely used to remove road marking lines. The machine has the advantages of strong power, high speed, easy and safe operation, low vibration, noise and dustproof etc. Engine: 13PS Honda Gasoline Engine Working width: 225mm Grinding thickness: adjusted according to the situation of road surface, normally less than 3mm Quantity of cutter: 78 pieces Cutter: Imported superalloy cutter, lifetime: 10000m² No. of shaft: 6 pieces